What’s a 3/2 Compressed Air Valve?


RecentlyI published an article on this particular site titled: What’s a 2/2 compressed air purifier? In the next installment in this series, is information about a marginally more complex air purifier; the 3/2 style.

The primary number in the 3/2 air compressor, both the KP-LOK toggle Valves three, describes to the variety of”working” air ports which are found inside the valve . That is, the number of vents that supply air to the valve, and then station the compressed air to whatever it’s the valve is assumed to accomplish.

Many 3/2 valves will probably have letters or numbers etched, painted or throw near each of their three”working” air vents. Whether there are numbers near the vents, the number 1 would be the source port to create the compressed atmosphere into that valve.

Port no 2 would be the working port from which air would flow to accomplish anything task that you wanted that valve todo.

The next port in a 3/2 air valve can be a”exhaust” jack of course, if required, it might be a 3 or a 5. If the vent designations at a 3/2 valve are letters, subsequently vent’A’ are the source port and interface’B’ the working interface, with the 3rd vent normally having an’E’.

As in the 2/2 valve there may be one or 2 additional vents from the endings of the 3/2 valve to permit an air signal line or lines to be attached. If this is the situation, this 3/2 valve will probably either be single, or double atmosphere piloted.

The two in a 3/2 atmosphere valve indicates the number of positions that the interior valve mechanism has. In cases like this, two. If this valve is operated or actuated, it will either open or close and air will either flow to the application upon actuation, or it will be prevented by flowing.

After the valve is not actuated, it’s ordinary condition is closed, and compacted air can’t move across it.

If your application requires air to flow through the valve when it’s not actuated, then that the circuit demands air to be flowing through this valve as it’s at rest, then a NO or normally open configured valve will be selected.

Each of 3/2 valves have actuators that’ll operate or’shift’ the atmosphere valve. An external buttontoggle, or possibly a solenoid actuator are the observable actuator. Inside, there will probably be an internal actuator – a spring – that may shift the valve into the off position once the outside actuator is not being used.

In the event the outside actuator is’detented’, then when the valve is worked, it will stay in it has last selected position until a operator changes it. This is useful when an operator needs to actuate the valve, and manually execute an alternative operation whereas the atmosphere valve feeds air into the application form.

Consequently, when the device has completed it’s function, and it’s time to’deflate’ it to let the compacted air back out, the third port in the 3/2 valve comes in to play.

Once the compressed air distribution KP-LOK toggle valve through the valve is shut off , a pathway through the valve into air will probably be opened, so allow the compressed air to escape. The air supply is shut, therefore the compressed air air flowing to the valve cannot flow through it, and the pressurized air which was formerly in the apparatus or application can now bleed backdown the atmosphere line through the valve to exhaust.

Thus, what type of devices are these?

Usually they are only acting type actuators. One comes to mind immediately;”Air springs”.

These are devices that look like wheels, but instead of have a opening in the middle of this doughnut at which the rim moves they have been shut on both sides with steel plates. At 1 side you will have an air vent to that an airline by a 3/2 valve is joined. These”air springs” are installed on their sides, imagine a drill lying apartment once you’ve taken off it your vehicle, and may generate enormous actuation forces. The application of air springs mirrors which of ordinary atmosphere compressors, yet offer large capacity in a fraction of the cost of an air cylinder of a essential size to generate the same force while the air spring.

The other application for 3/2 valves is just one acting air cylinders. A 3/2 valve is designed to do precisely that.

A handful of more points; the 3/2 valve can have the exhaust port emptied, and voila, there is a 2/2 valve.

If the cost of this valve is exactly the exact same, you need to use a 3/2 air-conditioning anywhere you may use a 2/2 valve. Since 2/2 valves consistently have to have the”working port” ultimately plumbed to atmosphere, that there is an exhaust port in a 3/2 valve provides no obstacle for it’s use.

For those who get a double acting air conditioner, also that you don’t have a 4/2 or 5/2 (more on these valves next article) available, you should use two 3/2 valves to work any cylinder that requires two distribution lines in order for this to extend and retract.

In ABOUT-air-compressors. Com my e book entitled All About Air Valves – Volume One is now available. If you are interested in more information about atmosphere valves, then do visit the site and down load a copy. This very first ebook is an introduction to air valves, also focuses on the 2/2 iteration. Future volumes will focus on 3/2 valves, and subsequently a 4/2 & 5/2 settings.

Continue Reading